Why Your Fence Stops Working
Check vegetation contact and grounding first — in community troubleshooting threads these two cause the large majority of sudden failures. Grass, weeds or a fallen branch touching the wire diverts energy to earth instead of down the fence line, and a poor ground connection does the same thing at the other end. Walk the line looking for green growth touching the conductor, then inspect your ground rod area before assuming the energizer has failed.
Touching vegetation gives the pulse a shortcut to earth. Instead of travelling the full length of the fence, the current leaks away at that point, so the shock drops along the rest of the line even though the energizer is running normally. This is why a fence can measure a healthy voltage at the energizer and still feel weak at the far end.
Most experienced keepers trim or graze rather than spray. A capable energizer will burn the grass back at the contact point on its own, while herbicide tends to leave you with tougher, woodier weed growth that is harder to control later — and you still have to deal with the dead material touching the wire.
Grounding, Soil & Vegetation
Check the system against the manufacturer’s spec: one to three steel ground rods, each driven at least 1.5 m (5 ft) into moist soil, connected to the ground terminal with 1.5 mm² insulated copper or aluminum wire and a firm, rust-free joint. The energizer’s own panels are the built-in signal — the short-circuit indicator glows steadily when the fence or the ground circuit is leaking. If it does, fix the ground before you spend money on a bigger energizer.
The manufacturer’s manual specifies one to three steel ground rods, each driven at least 1.5 m (5 ft) into soil that stays damp. It does not set a spacing figure — what matters is that every rod reaches moist, conductive soil, so site them where moisture persists.
Yes, significantly — dry soil is one of the most common causes reported in community threads. Wetting the ground rod area is the standard field fix, and the long-term answer is to site rods where moisture persists, or use more rod length. Never rely on watering alone as a permanent solution.
Yes. Tape or wire contacting a post creates a leakage path to earth, the same way touching vegetation does. Posts in poor condition, sagging lines, and damaged insulators are all common culprits.
Installation, Energizer Choice & Maintenance
Professional install guidance points to roughly 5,000–10,000 volts on the fence line, typically using 4 to 7 strands depending on the animals being contained.
Fix the fence before you upsize the energizer. If the weakness comes from vegetation contact or poor grounding, a bigger unit simply pushes more energy into the same leak. High joule output paired with low impedance and a visible readout is the combination that matches this problem — high energy to push through, low impedance to maintain voltage under load, and a display so you can see what is actually happening.
Because the failure modes users report — weak shock, sudden stop, voltage that looks fine at the box — are overwhelmingly caused by grounding and vegetation, not by the energizer itself. That is why grounding and vegetation management belong on the product page, not buried in a manual.
Plan on walking and clearing the line about every two weeks during the growing season, and checking voltage weekly. Most of the work is vegetation and grounding, not equipment.
Reported maintenance runs roughly 200 to 500 US dollars per mile per year in materials and time. That figure is what makes a reliable energizer and correct installation economically meaningful over the life of the fence.
Informations sur l'expédition
Nous nous engageons à vous livrer votre commande dans les meilleurs délais et dans les meilleures conditions. Toutes les commandes sont traitées avec soin dans un délai de 1 à 2 jours ouvrables après que vous les ayez passées. Une fois votre colis expédié, vous pouvez vous attendre à une livraison dans un délai de 5 à 7 jours ouvrables, selon votre lieu de résidence.
Nous traitons les commandes rapidement pour vous les faire parvenir dans les plus brefs délais. Si vous avez besoin de modifier ou d'annuler votre commande, veuillez nous contacter dans les 12 heures suivant votre achat.
Absolument. Une fois votre commande expédiée, vous recevrez un numéro de suivi par e-mail afin que vous puissiez suivre son acheminement jusqu'à votre porte.
Coordonnées de paiement
We accept Visa, Mastercard, American Express, Discover, JCB, Diners Club and PayPal, plus Google Pay for accelerated checkout. All orders are billed in US dollars.
All prices are listed and charged in US dollars (USD). If your card is issued in another currency, your bank converts the amount at its own exchange rate, and any conversion fee is set by your bank rather than by us.
Payment is captured when your order is placed, and your order is then processed for dispatch within 1–2 business days.
Checkout runs on Shopify's hosted, PCI-DSS compliant checkout platform. We never see or store your full card number — payment details go directly to the payment processor, and the store is served over HTTPS.